Cloverleaf Pond Heaters

These all new Cloverleaf Pond heaters are fully EU, TUV, & UL approved and they are available in two sizes 1 Kw and 2 Kw.

These Cloverleaf heaters are very easy to install into new or existing pond setups and come complete with both rigid and flexible pipe connections. Choose from connection via 19mm, 25mm or 38mm flexible pond hose using the two hosetails supplied or alternatively these Cloverleaf heaters wil accept 40mm rigid solvent weld or 1.5" rigid pressure pipe. These simple easy to use pond heaters have a minimum flow rate of 4000lph and have a safety low flow shut off switch for peace of mind

For maximum efficiency and to maintain an ambient temperature the pond should be covered and insulated to help achieve and maintain the water temperature. In cases of insufficient insulation more Kw per gallon/lites may be required depending on the level of desired water temperature.

Two models are available in the Cloverleaf Pond Heater range, these are the 1 Kw for up to 1000 gallons (4500ltrs) and the 2 Kw for ponds up to 2000 gallons (9000 Ltrs).

Cloverleaf Pond Heater Specifications:

• 1 Kw and 2 Kw power consumption.
• 4000 lph minimum flow rate with pressure switch.
• Thermostatically controlled.
• IP55 rated.
• 1.5 m cut end cable fitted
• Flexi hosetails plus solvent weld inlet and outlets.
• Dimensions: 230 cm (l) x 18.5 cm (w) x 18.5 cm (h)

Note on Installation:

We recommend that isolation valves are installed either side of the heater, this will facilitate the removal of the heater so that it can be flushed out on a regular basis and keep the heating element in prisitne condition. Here at Dankoi we supply a full range of fittings so if unsure what you require please don't hesitate to contact us.

Cloverleaf Pond Heaters

These all new Cloverleaf Pond heaters are fully EU, TUV, & UL approved and they are available in two sizes 1 Kw and 2 Kw.

These Cloverleaf heaters are very easy to install into new or existing pond setups and come complete with both rigid and flexible pipe connections. Choose from connection via 19mm, 25mm or 38mm flexible pond hose using the two hosetails supplied or alternatively these Cloverleaf heaters wil accept 40mm rigid solvent weld or 1.5" rigid pressure pipe. These simple easy to use pond heaters have a minimum flow rate of 4000lph and have a safety low flow shut off switch for peace of mind

For maximum efficiency and to maintain an ambient temperature the pond should be covered and insulated to help achieve and maintain the water temperature. In cases of insufficient insulation more Kw per gallon/lites may be required depending on the level of desired water temperature.

Two models are available in the Cloverleaf Pond Heater range, these are the 1 Kw for up to 1000 gallons (4500ltrs) and the 2 Kw for ponds up to 2000 gallons (9000 Ltrs).

Cloverleaf Pond Heater Specifications:

• 1 Kw and 2 Kw power consumption.
• 4000 lph minimum flow rate with pressure switch.
• Thermostatically controlled.
• IP55 rated.
• 1.5 m cut end cable fitted
• Flexi hosetails plus solvent weld inlet and outlets.
• Dimensions: 230 cm (l) x 18.5 cm (w) x 18.5 cm (h)

Note on Installation:

We recommend that isolation valves are installed either side of the heater, this will facilitate the removal of the heater so that it can be flushed out on a regular basis and keep the heating element in prisitne condition. Here at Dankoi we supply a full range of fittings so if unsure what you require please don't hesitate to contact us.